Replacement Belts for RCA Turntables Back to Belts Index Belt Specifications Chart TT Basics Home Page
<!--end title--!>
| RCA 11-2017A | Belt SCX 7.0 | Special Order |
| RCA 11-2017A | Belt SCY 4.2 | Special Order |
| RCA RCA 11-3017A | Belt SCX 7.0 | Special Order |
| RCA RCA 11-3017A | Belt SCY 4.2 | Special Order |
| RCA RCA 11-4022B | Belt SCX 7.0 | Special Order |
| RCA RCA 11-4022B | Belt SCY 4.2 | Special Order |
| RCA 63-27747 | Idler Wheel IW08 | Special Order |
| RCA 229 | Idler Wheel IW05 | Special Order |
| RCA 230 | Idler Wheel IW05 | Special Order |
| RCA 231 | Idler Wheel IW05 | Special Order |
| RCA 1000 | Idler Wheel IW08 | Special Order |
| RCA 2000 | Idler Wheel IW08 | Special Order |
| RCA 3000 | Idler Wheel IW08 | Special Order |
| RCA RP-205-190 Series | Idler Wheel IW04 | Special Order |
| RCA RP-211 | Idler Wheel IW05 | Special Order |
| RCA RP-212 | Idler Wheel IW05 | Special Order |
| RCA RP-212-107 Series | Idler Wheel IW05 | Special Order |
| RCA RP-215 | Idler Wheel IW05 | Special Order |
| RCA RP-216 | Idler Wheel IW05 | Special Order |
| RCA RP-220 | Idler Wheel IW05 | Special Order |
| RCA RP-226 | Idler Wheel IW05 | Special Order |
| RCA RP-227 | Idler Wheel IW05 | Special Order |
| RCA RP-228 | Idler Wheel IW05 | Special Order |
| RCA RP-229 | Idler Wheel IW04 | Special Order |
| RCA RP-230 | Idler Wheel IW05 | Special Order |
| RCA RP-230 (early) | Idler Wheel IW04 | Special Order |
| RCA RP-231 | Idler Wheel IW05 | Special Order |
| RCA RP-231 (early) | Idler Wheel IW04 | Special Order |
| RCA RP-232 | Idler Wheel IW05 | Special Order |
| RCA RP-233 | Idler Wheel IW05 | Special Order |
| RCA RP-233-3 | Idler Wheel IW05 | Special Order |
| RCA VLP-34J | Tire ST 1.86 | Special Order |
| RCA YJP-41W/J/E | Idler Wheel IW05 | Special Order |
| RCA Z-1132 | Idler Wheel IW04 | Special Order |
| RCA Z-1142 | Idler Wheel IW04 | Special Order |
| IW05
ID=.123 in. OD=1.885 in. C/S=.557 in. |
IW08
ID=.153 in. OD=2.015 in. C/S=.409 in. |
If your turntable is not listed, first look for a close match in model number. Or, take careful measurements of your old belt's inside circumference, width and thickness.
Make the measurements with the belt lying flat and unstretched. Use a paperclip to mark your starting point. Measure in inches to match model; one inch=25.4mm. Also, make note of how loose the old belt is while installed in the turntable. Does it slip? How much side-to-side deflection is there in the open section between the spindle and the platter? Depending on how badly stretched out your old belt is, deduct 5 to 10 percent from the circumference. If the belt is broken or missing, use a piece of string (wrapped without slack, but not stretched) to measure the proper circumference, and then deduct 10 percent to allow the new belt to stretch into place. Go to the Belt Specifications Chart to find a suitable replacement.