Replacement Belts for Dual Turntables Back to Belts Index Belt Specifications Chart TT Basics Home Page
<!--end title--!>
| Dual 502 | Belt FRA 19.6 | In Stock $10.00 |
| Dual 504 | Belt FR 20.0 | In Stock $10.00 |
| Dual 506 | Belt FR 20.0 | In Stock $10.00 |
| Dual 510 | Belt FR 19.6 | In Stock $10.00 |
| Dual 521 | Belt FR 20.0 | In Stock $10.00 |
| Dual 522 | Belt FRY 13.1 | Special Order |
| Dual 601 | Belt FRA 19.6 | In Stock $10.00 |
| Dual 1009 | Belt FR 20.0 | In Stock $10.00 |
| Dual 1010/A/S | Belt FR 20.0 | In Stock $10.00 |
| Dual 1011 | Belt FR 20.0 | In Stock $10.00 |
| Dual 1014 | Belt FR 20.0 | In Stock $10.00 |
| Dual 1015 | Belt FR 20.0 | In Stock $10.00 |
| Dual 1016 | Belt FR 20.0 | In Stock $10.00 |
| Dual 1019 | Belt FR 20.0 | In Stock $10.00 |
| Dual 1209 | Belt FRY 25.0 | In Stock $10.00 |
| Dual 1212 | Belt FRY 25.0 | In Stock $10.00 |
| Dual 1218 | Belt FRY 25.0 | In Stock $10.00 |
| Dual 1237 | Belt FRA 19.6 | In Stock $10.00 |
| Dual 1241 | Belt FRA 19.6 | In Stock $10.00 |
| Dual 1242 | Belt FRX 20.7 | In Stock $10.00 |
| Dual 1245 | Belt FRA 19.6 | In Stock $10.00 |
| Dual 1246 | Belt FRA 19.6 | In Stock $10.00 |
| Dual 1249 | Belt FRA 19.6 | In Stock $10.00 |
| Dual 1256 | Belt FRY 13.1 | Special Order |
| Dual 1257 | Belt FRY 13.1 | Special Order |
| Dual 1264 | Belt FRY 13.1 | Special Order |
| Dual C-1268 | Belt FRY 13.1 | Special Order |
| Dual CS-505/-1 | Belt FRY 13.1 | Special Order |
| Dual CS-506/-1 | Belt FRY 13.1 | Special Order |
| Dual CS-528 | Belt FRY 13.1 | Special Order |
| Dual CS-1258 | Belt FRY 13.1 | Special Order |
| Dual CS-5000 | Belt FRY 25.0 | In Stock $10.00 |
| Dual M12B1-12 | Belt OC 18.0 | Special Order |
If your turntable is not listed, first look for a close match in model number. Or, take careful measurements of your old belt's inside circumference, width and thickness.
Make the measurements with the belt lying flat and unstretched. Use a paperclip to mark your starting point. Measure in inches to match model; one inch=25.4mm. Also, make note of how loose the old belt is while installed in the turntable. Does it slip? How much side-to-side deflection is there in the open section between the spindle and the platter? Depending on how badly stretched out your old belt is, deduct 5 to 10 percent from the circumference. If the belt is broken or missing, use a piece of string (wrapped without slack, but not stretched) to measure the proper circumference, and then deduct 10 percent to allow the new belt to stretch into place. Go to the Belt Specifications Chart to find a suitable replacement.